Effect of retained austenite – Compressive residual stresses on rolling contact fatigue life of carburized AISI 8620 steel

In this study the rolling contact fatigue (RCF) of case carburized AISI 8620 steel was numerically and experimentally investigated. For the numerical study, a two dimensional finite element (FE) RCF model based on the continuum damage mechanics (CDM) was developed to investigate the fatigue damage accumulation, crack propagation and final fatigue life of carburized AISI 8620 steel under various operating conditions. A randomly generated Voronoi tessellation was used to model the effects of material microstructure topology. The boundaries of the Voronoi elements were assumed to be the weak planes where damage accumulates, cracks initiate and propagate to simulate inter-granular cracks. A series of torsional fatigue tests were conducted on carburized AISI 8620 steel specimens containing 0% and 35% retained austenite (RA) to determine fatigue load (S) vs. life (N) of the material. The S–N results were then used to determine the material parameters necessary for the rolling contact fatigue model. The torsional fatigue test results indicate that the carburized AISI 8620 specimens with higher RA demonstrate higher life than the specimens with lower RA. The RCF model also indicates that the material with higher level of compressive residual stresses (RS) and retained austenite demonstrates higher RCF life. In order to corroborate the results of RCF model, a three-ball-on-rod rolling contact fatigue test rig was used to determine the RCF lives of carburized AISI 8620 steels with different amounts of RA. The fatigue life and cracks evolution pattern from the numerical and experimental results were corroborated. The results indicate that they are in good agreement.     

Investigation into eddy current pulsed thermography for rolling contact fatigue detection and characterization

This paper reports on the use of eddy current pulsed thermography (ECPT) for detection and characterization of rolling contact fatigue (RCF). Detection mechanisms with eddy currents and heat propagation effects were discussed with RCF modeled as a simple angled defect. Two different angled defects were studied through numerical simulations and experimentally by using uniform magnetic field (UMF) excited by Helmholtz coils. Finally, a rail sample with RCF defects was inspected using UMF excitation. It is shown that ECPT with UMF excitation provides an efficient and robust method to detect angled defects, compared with nonuniform magnetic field (NUMF) excitation.     

基于C#的飞机疲劳试验实时预警系统设计

为满足飞机疲劳试验对试验数据实时监控的需求,采用C#语言开发了一套飞机疲劳试验实时预警系统。该系统以疲劳试验数据管理系统为基础,计算各测量点、各工况的平均值和标准差,通过多种方法设定预警阈值。该系统界面友好、功能完备,可实现疲劳试验数据的实时监控,能够及时发现异常试验数据,尽早发现结构损伤并采取有效措施,可以大幅降低维修成本、缩短维修周期。     

The visual impact of augmented reality during an assembly task

Many studies have shown the benefits of augmented reality (AR) to improve manufacturing and control processes in industry. However, the presentation of AR content through optical see-through head-mounted displays may induce unnatural viewing conditions, which consequences on the user’s visual system have not been investigated yet. This study aimed at assessing whether using AR instructions to guide a manual task, i.e., conditions where the user is forced to repeatedly look at and accommodate in different planes to extract information from both real and virtual environments, could potentially impact the visual system of operators. A before/after design study was carried out, asking 26 participants to perform Lego assemblies for 30 min with either paper or AR instructions. The effects of using AR compared to paper instructions were evaluated both on binocular vision, with classical optometric measurements, and on visual fatigue, with the Virtual Reality Symptoms Questionnaire. No clinically significant differences in optometric measurements (far/near visual acuity, stereoacuity, phoria, convergence, fusional amplitude, accommodation amplitude, accommodative convergence) have been found between AR and paper instructions, and only negligible fatigue symptoms have been seen specifically for AR. Results from both objective and subjective measurements suggest that there is no impact of AR on the oculomotor system and that, in this specific case of use, AR can be safely used for production operators.     

感应淬火对曲轴扭转疲劳性能的影响

目的研究感应淬火对曲轴扭转疲劳性能的影响,为曲轴的设计和制造工艺调整提供技术参考。方法开展淬火曲轴和未淬火曲轴的扭转疲劳强度试验,利用升降法得到疲劳试验结果,从试验数据和微观组织等方面开展分析和讨论。结果未经过淬火的曲轴在99.9%存活率下的扭转疲劳极限为967.6N·m,经过感应淬火的曲轴在99.9%存活率下的扭转疲劳极限为1361.2N·m。感应淬火后曲轴的表面形成深度约3.5 mm的淬火层,平均硬度为HV0.5600,金相组织为细针状马氏体。曲轴的失效情况均为连杆颈油孔处开裂。结论 38MnVS6非调质钢曲轴在感应淬火后的扭转疲劳极限提升了约41%,曲轴油孔内壁的加工缺陷是形成裂纹源的主要原因,对曲轴淬火层区域的油孔内壁进行一定的表面处理,可进一步提高曲轴的扭转疲劳强度。     

粉土界面恒刚度循环剪切试验研究

竖向循环荷载作用下桩土界面的作用机理是研究桩土摩擦疲劳的关键。针对循环荷载作用下桩-粉土界面的剪切性能,使用改进的剪切试验装置在恒刚度条件下进行循环剪切试验,研究循环次数、累积位移和法向刚度对其摩擦疲劳性能、循环后单调剪切性能的影响。试验结果表明,粉土在循环剪切过程中,法向应力和剪应力在初始10个循环内随循环数增加快速衰减,随着循环进行,逐渐趋于稳定;单次循环内在剪切位移方向变化时,土体呈现表现出剪缩-剪胀-剪缩交替现象,总体变形呈现剪缩的趋势;循环荷载作用下,粉土界面的法向应力和剪应力随法向刚度增大衰减速率增大,达到稳定的累积循环位移越小;粉土循环后的单调剪切、法向应力恢复的单调剪切的剪应力比小于首次单调剪切试验值,且法向应力恢复的循环后剪切试验的剪胀程度较小,表明循环剪切过程中界面处粉土颗粒棱角破碎,颗粒变得光滑。在对试验数据分析的基础上,提出了与累积位移、法向刚度和初始应力相关的无量纲累积位移,建立了法向应力和界面摩擦角随累积位移的衰减方程。     

Behavior of 316L stainless steel containing corrosion pits under cyclic loading

The environmental performance of 316L grade stainless steel, in the form of tensile specimens containing a single corrosion pit with various aspect ratios, under cyclic loading in aerated chloride solutions is investigated in this study. Results from environmental tests were compared and contrasted with those obtained using finite element analysis (FEA). Fractography of the failed specimens obtained from experiments revealed that fatigue crack initiation took place at the base of the shallow pit. The crack initiation shifted towards the shoulder and the mouth of the pit for pits of increasing depth. This process is well predicted by FEA, as the strain contour maps show that strain is the highest around the centric strip of the pit. However, for shallow pits, local strain is uniformly distributed around that strip but begins to concentrate more towards the shoulder and the mouth region for increasingly deep pits.     

In vitro cyclic fatigue and hydrothermal aging lifetime assessment of yttria-stabilized zirconia dental ceramics

The in vitro lifetime assessment of dental zirconia has been the focus of researchers. This work mainly studied the cyclic fatigue lifetime in saliva and aging lifetime of three commercial zirconia dental materials: two kinds of 3 mol%-yttria stabilized zirconia ST(super-translucence) and MT(medium-translucence), in which MT contains a small amount of alumina; a 5 mol%-yttria stabilized zirconia TT(tooth-translucency). ST and MT materials have higher initial mechanical strength (flexural strength) and initial crack propagation threshold than TT materials, thus they have longer cycle fatigue lifetime, but TT has best aging resistance(no aging) in existing aging procedures. MT has a higher initial mechanical strength and better aging resistance than ST samples due to the influence of alumina at grain boundary, but has lower strength reliability. Finally the service lifetime of the three materials was evaluated, and some guidance for their use is provided.     

H13钢等离子堆焊Ni60A/Cr3C2覆层的磨损及热疲劳性能

采用等离子堆焊技术在H13钢基体表面上制备了Ni60A/Cr₃C₂堆焊覆层,研究了覆层的磨损行为和热疲劳性能。在600 ℃下销盘试验的结果表明,镍基碳化铬复合覆层的耐磨性是Ni60A堆焊覆层的2.8倍和基材H13钢的11.6倍。镍基覆层可以显著降低H13钢的摩擦因数,加入碳化铬则会削弱覆层的摩擦性能。随着磨损的进行,主要磨损机理从氧化磨损演变为磨粒磨损和粘着磨损。在800 ℃到室温下的热疲劳测试结果表明,镍基碳化铬复合覆层在48个热循环后疲劳裂纹达到200 μm,早于镍基覆层的62次。这说明高温氧化促进热疲劳裂纹的产生。碳化铬增强相从镍基上剥离,导致镍基复合覆层热疲劳性能下降。     

Influence of domain switching process on the electrical fatigue behavior of ferroelectrics

We report an experimental approach, designed based on the recent findings that domain switching in ferroelectric ceramics can be separated into three regimes during antiparallel electric field loading, to investigate the influence of domain switching process on the electrical fatigue behavior of ferroelectrics. Uniaxial compressive stress (−2 MPã -100 MPa) and thermal loading (20 °C–150 °C) were used to tune the domain switching process. Under the same loading condition, the bipolar electrical fatigue behavior of soft lead zirconate titanate ceramics was systematically characterized. The amplitude and frequency of the applied electric field are 2 kV/mm and 10 Hz, respectively. By analyzing the evolution of the domain switching process, combined with the measured polarization and strain response, as well as the cracks observed on the surface of the specimen, it is found that the fatigue of ferroelectric ceramics was mainly related to the domain switching process near the coercive electric field: the regime 2 defined in this paper. The underlying mechanism was further discussed by considering the interplay between the domain switching process with the main factors affecting the electrical fatigue of ferroelectrics, namely defect redistribution, charge carrier injection, and crack initiation.